Showing posts with label appliance zone. Show all posts
Showing posts with label appliance zone. Show all posts

Wednesday, December 11, 2013

Energy Saving Tips In Regards To Kitchen Appliances

From Appliance Zone

Appliance Zone Part Search


Kitchen appliances in the modern modular kitchens have become an integral part of food preparation and preservation. Besides, the multipurpose air conditioners and gas burners have added more levels of comfort to the kitchen. All these appliances use energy. Inefficient usage could lead to huge bills on the energy consumption. Besides, malfunctioning or poorly maintained and under repaired equipment can add some extra dollars to the energy bill. However there is a solution to this problem.
Energy saving can be done in many ways. Just go into your kitchen with a pen and a paper and list out the electrical and gas appliances you have. You could find Lighting bulbs and Tubes: - Kitchen lighting is one of the fundamental elements that need energy. Try replacing your existing lighting with energy saving LED bulbs. They use less power compared to traditional bulbs. Switch off the lighting when not needed. Avoid too much of lighting ornamentation in the kitchen. In case any plug point or cabling is malfunctioning or has a loose contact make it a point to get your appliance repair done quickly. Open cables are a source of energy loss and safety hazard.
Air conditioners and heaters: - They consume more energy compared to your lighting system. Preventive maintenance and frequent appliance repair of malfunctioning parts helps in saving energy. Use these appliances only when you are physically present in the kitchen.
Ovens and food heaters: - They are the key elements of the kitchen and hence need to be maintained with maximum care. They are more prone to wear and tear and frequency of fail is more in these appliances. There are many appliance repair companies in your neighborhood regions. You can browse online to find a reliable service provider and get these kitchen appliances repaired that help you in more energy saving.
The kitchen hearth (Stove) is a complex appliance that gets gas supply from cylinders or pipelines. Poorly maintained hearth could result in almost double the energy consumption than normal. Frequent maintenance services are undertaken by many online companies who also undertake appliance repair services.
You could do energy saving in many other ways also. Do keep any food directly from the refrigerator into the over or hearth for heating. It takes additional amount of energy. Keep the food in room temperature for 5-10 minutes before heating it. Always keeps your refrigerator door closed for better energy saving. Do not over stuff the refrigerator and leave some space for air circulation. If you are using room heaters in the kitchen, make it a point to get it serviced from a reliable appliance repair and servicing company.  There are many service providers who take care of periodical appliances maintenance in your region. You could obtain their services and keep your kitchen appliances running in good condition

Friday, November 15, 2013

Doing Any Holiday Traveling?

 

 

Travel in comfort...

 ApplianceZone has what you need to make sure you can get your gobble-gobble on wherever you go this holiday season.

Appliance Parts and More!

  • We not only carry parts for you RV appliances, but for awnings, steps and more.
  • Browse through our RV part categories to find what you need.

RV Awning Parts RV AC Parts RV Washer / Dryer Parts RV Furnace Parts RV Microwave Parts
RV Refrigerator Parts RV Step Parts RV Stove/Oven/Range Parts RV Toilet Parts RV Water Heater Parts

Thursday, May 30, 2013

Something BIG is Coming Soon

Something BIG is Coming Soon

 
Here at Appliance Zone there has been a huge development underway that will change this industry. We value all of our customers and we want to show our appreciation for their loyalty. It is Appliance Zone's goal to empower individuals with a Do-It-Yourself attitude and provide all the necessary tools to accomplish any task! With the economy we understand the meaning of "pinching every penny". This new feature will not only reward our customers for their loyalty but will also give benefits and additional discounts that are out of this world! So stay tuned for the upcoming newsletters that will reveal more about this new feature and the launching date.
 
 

Wednesday, May 8, 2013

Kenmore 11081860110 Washing Machine That Fills, Spins and Drains but Will Not Agitate

Here is a transcript of a recent online posting of a Kenmore washing machine repair issue from the Appliance Zone Repair Forum. Hopefully it will give you some guidance if you have the same issue. For any other repair questions make sure to check out the Appliance Zone Repair Forum!

Question:

We have a Kenmore 11081860110 that fills, spins and drains but will not agitate.
In Agitate area of dial (any agitate area) Motor does not run but timer ticks.
I'm also having trouble reading the wiring diagram.


Tech:

Thank you this could be two things ,either a timer contact internally in the timer .
Or the drive motor itself .
for agitation it turns one way for drain and spin it turns the opposite way .
you would have to measure voltage to the motor to see which it is.

Question:

I think the motor is fine.
Here are the motor resistance readings with harness disconnected:

Motor Harness
Open GRN
W W
NoPin Open
NoPin Open
Open RED

Meter Resistance
PROBE PROBE 0.3
Motor
W BLU 1.5
W W/BLK 0.3
YEL RED 7.6

BLK YEL 7.6

BLK W >20M
BLK W/BLK >20M

I remember *somewhere* reading that for a direct drive if you swap 2 wires and put it in
"SPIN" then it should agitate, (assuming it spins in the normal configuration). I haven't found
that *somewhere* again. Would this work as a test?

Also on the distorted, difficult to read wiring diagram I have (3351735) I assume the #s
next to the switches are the timer positions and that the lack of odd "SW. Function's was
for "readability", is that correct?

I suspect the timer (3951734) since I hear no 60Hz from the motor in the agitate mode.

I have the tub filled enough to run on low level.

In the "Cotton/Sturdy" mode I suspect I should see low resistance across the power plug in the agitate mode as I do in the spin state.

Resistance across plug
Cotton/sturdy spin 1.8
Permanent Press spin 2.28K
Delicate spin 2.28K

After spraying timer with contact cleaner
Resistance across plug
Cotton/sturdy spin 1.8
Permanent Press spin 2.25K
Delicate spin 2.25K

Cotton/sturdy agitate 2.25K
Permanent Press spin 2.25K
Delicate spin 2.25K

Tech:

Just go down to the motor at Yellow and Red with the unit in an agitation mode check for 120 volts A/C if you have voltage it the motor if no voltage it is the timer 1

Question:

There is a momentary jump on the DVM set at 200VAC then returns to 0.00.
Based on this I'll get a new timer and post the resolution here.


Tech:

Yes that sounds like the issue .good luck

Tuesday, April 30, 2013

How to Repair a Leaky Water Dispenser

To check the tubing for a leak, tilt your refrigerator back so you can see the tubing underneath and have someone press the water dispenser. If there's a leak there, you'll see it.
 
 
Fixing the problem is just as easy as diagnosing it. All you need is some replacement tubing and a couple quick connect couplers.
Locate the area where the leak is and cut it out. (Use a sharp utility knife to avoid distorting the tubing.) Cut the replacement tubing to size and use the couplers to connect it to the tubing that remains under the fridge.
.

Monday, April 15, 2013

Leaky Washing Machine

Do you have a leaky washing machine but can't seem to figure out where the water is coming from? Here are a few tips to point you in the right direct. If you're still unsure then head over to our repair forum at http://forum.appliancezone.com .


Here are some of the common areas that your washer may leak:
Inlet Hose Connections - Check for drips around the supply hose connection on the back of the washer as it fills with water. If the hoses are old, corroded or rusted replace them. But if they're in good shape you can replace just the hose's internal washers.
 
Hose Connectors - Open the cabinet and start the fill cycle. These hoses tend to leak around a worn out clamp, but the hoses themselves can also crack and break. Identify what is causing the leak and replace it.
 
Pump - Open the cabinet and check around the pump. The pump will typically leak around the pulley. If you notice this, the pump will need to be replaced.

Friday, March 22, 2013

Model Number Search Now Available on ApplianceZone.com

Since Appliance Zone opened its doors in 2008, customers have persistently requested the ability to search their appliance' model numbers so they can research and locate parts more easily on their own. For many years we have attempted to find a comprehensive solution to appease this demand, but have been unsuccessful, until now.


 

To use the model look-up simply click on the "Search by Model" tab at the top of the Start Here box on our home page. Then just start typing in your model number. As you type you will notice the model options available for what you've typed so far, making it easier for you to select the correct number for your appliance. Once your full model number has been inserted, click "GO!" to view all of the available parts for your model. If you still have trouble locating your part, our customer service reps are available via chat to assist.

Appliance Zone has always tried to empower customers with a DIY attitude. We've been working hard the past few months, developing new tools and incentives to assist and reward our loyal customers. This new model number search feature is just one of many to come.

So, be sure to stay tuned for more exciting announcements from ApplianceZone.com!

Friday, March 15, 2013

What is the Appliance Zone Repair Forum?

The Appliance Zone Repair Forum is the premier spot to get all of your repair questions answered free of charge. Are you stuck on how to repair an issue with your appliance? Just post your question on this forum and you'll get a quick and reliable answer! Check it out live ----> HERE!

 

 

Thursday, March 14, 2013

Video Contest Entry

One of the entries into our video contest. We are still accepting submissions until March 31st.

Tuesday, March 5, 2013

Maintaining Your Trash Compactor


The parts of your trash compactor that should be cleaner regularly are those that come into contact with trash the most frequently. This includes the ram, which is what presses the garbage down into the bag, and the container that holds the bag, which may become torn and leak onto the container. Cleaning both of these parts regularly will eliminate odors and keep mold from growing on and in your appliance.

Things You'll Need:


• Water and dish soap (or all-purpose cleaner) Rubber gloves Wet/dry vacuum Rag or sponge Antibacterial cleaner (or 1/4 to 1/2 cup bleach and 1 gallon water) Bleach

Step 1


Use an all-purpose cleaner or water and dish soap to wipe down (with a rag or sponge) the front of the machine. If it is stainless steel, consider using a cleaner made specifically for that material.

Step 2


Put on rubber gloves before cleaning the compactor's interior for hygiene and to avoid being cut by loose shards of glass or metal parts.

Step 3


Pull out the drawer and use a wet/dry vacuum to suck out any loose glass, metal or other debris.

Step 4


Spray an antibacterial cleaner onto the interior surface of your trash compactor's container (where the bag goes) and the ram, the flat part that pushes down the garbage. Though available at drug, grocery and hardware stores, antibacterial cleaner can also be made at home with water and a bit of bleach. Mix 1/4 to 1/2 cup bleach per gallon of water; wipe it on with a sponge or rag.

Step 5


Allow the areas to air-dry before putting in a fresh trash bag and closing the drawer.

• Spray the inside of your trash compactor with a disinfectant between cleanings to discourage bacteria from growing. If your compactor has a filter, replace it once or twice a year.



Tuesday, February 19, 2013

Maintaining Your Garbage Disposal

This post original appeared HERE
 The parts of your trash compactor that should be cleaner regularly are those that come into contact with trash the most frequently. This includes the ram, which is what presses the garbage down into the bag, and the container that holds the bag, which may become torn and leak onto the container. Cleaning both of these parts regularly will eliminate odors and keep mold from growing on and in your appliance.

Things You'll Need:

• Water and dish soap (or all-purpose cleaner) Rubber gloves Wet/dry vacuum Rag or sponge Antibacterial cleaner (or 1/4 to 1/2 cup bleach and 1 gallon water) Bleach

Step 1

Use an all-purpose cleaner or water and dish soap to wipe down (with a rag or sponge) the front of the machine. If it is stainless steel, consider using a cleaner made specifically for that material.

Step 2

Put on rubber gloves before cleaning the compactor's interior for hygiene and to avoid being cut by loose shards of glass or metal parts.

Step 3

Pull out the drawer and use a wet/dry vacuum to suck out any loose glass, metal or other debris.

Step 4

Spray an antibacterial cleaner onto the interior surface of your trash compactor's container (where the bag goes) and the ram, the flat part that pushes down the garbage. Though available at drug, grocery and hardware stores, antibacterial cleaner can also be made at home with water and a bit of bleach. Mix 1/4 to 1/2 cup bleach per gallon of water; wipe it on with a sponge or rag.

Step 5

Allow the areas to air-dry before putting in a fresh trash bag and closing the drawer.

• Spray the inside of your trash compactor with a disinfectant between cleanings to discourage bacteria from growing. If your compactor has a filter, replace it once or twice a year.

Tuesday, February 12, 2013

Washing Machine Problem/Solution

The washing machine is up there with the refrigerator and the heater/AC unit as one of the three most vital home appliances in modern life. When any of these three machines goes south, it can be cause for alarm. Unlike with the other two, however, repairing the washing machine does not automatically entail a service call from a professional.





Prevention/Solution
Leaking is a common problem with washing machines. The first thing to do is to locate the exact spot from which the machine is leaking. The problem is that a washing machine has many places from which water may leak. Check all hoses and look for cracks in the unit itself. Tightening a nut or a screw may be all that is necessary.

Prevention/SolutionLeaking may occur before or after the machine has filled. If a machine leaks after it has already filled with water, this indicates that the leak may be the result of loose connections or a problem with a pump hose. If the leaks occur during the filling process, this indicates a possible crack in an inlet hose.

Prevention/Solution
Almost all washing machines vibrate to a degree, but excessive vibration indicates that the level of the legs is off-kilter. The racket a vibrating machine makes might seem to indicate a problem that would be very expensive to fix, but in most cases the solution is as simple as propping up one corner of the machine with a piece of wood, or even tightening an adjustable leg with a screwdriver.

Prevention/Solution
A washing agitator that spins too roughly or too slowly is usually the result of a drive belt that is either broken or has come too loose. Inspecting the belt for wear or checking for looseness is the first thing you should do if your machine is suffering agitation problems. Tightening a loose belt typically requires little more than a socket wrench to loose and tighten the nuts. Even replacing a belt is not difficult enough to require a professional.

Prevention/Solution
When water enters a washing machine too slowly or not at all, the problem is normally located in a kink or blockage in the inlet hose that carries water into the well. A pair of hose pliers can be used to remove the hose from the inlet valves. Simply straighten out the hose. If this does not solve the problem, remove the screens from over the values and rinse them under water.

Prevention/Solution
If the tub of water overflows, the first thing to do is unplug the washing machine. If the flow of water continues, turn off the water faucet, remove the water and replace the inlet valve. Replacing the inlet valve is a relatively easy operation involving the removal of the top of the valve and the replacement of the inlet hose. Typically, all that is required is a screwdriver, and and possibly a dull knife.

Warning
If the flow of water halts after you unplug the washing machine, it is a sign of a defective water-level switch. Fixing it is a much more complicated process that requires a professional. While many minor repairs and maintenance of washing machines can be done by the homeowner, if the repair does not solve the problem, it is better to call in a professional than to continue trying to fix it yourself, as you may end up doing even greater damage to the unit.

The original article can be found on our repair forum at www.forum.appliancezone.com

Tuesday, February 5, 2013

GE Stacked WSM2420SEZWW Faulty Thermal Fuse

More great advice on the Appliance Zone Forum!


Question: I want to know how to access and identify the thermal fuse for testing and probable replacement. I have dropped the front panel but cannot identify the fuse. Does this have to be accessed from the rear of the unit? I remember watching the repairman repair this 4 years ago and thought it had been accessed from the front. Any advice. Thanks.

Answer from Kelly Smith on the Appliance Zone Forum: Hi, thanks for your inquiry. The Thermal Fuse is accessed from the back of the unit, once the rear access panel has been removed. It is shown as number 294 in the diagram, pictured and available below.
Here is a link to the correct part ------ Click Here

Tuesday, January 29, 2013

Huge Appliance Zone Video Contest $$$

Do you use Appliance Zone parts? Are you or someone you know handy with a video camera? Could you use $500? If you answered yes to these questions then boy do we have a contest for you! Create a video of yourself either showing you make a repair using parts from Appliance Zone or a testimonial of how Appliance Zone parts have helped you out and you could win some great prizes. Here are the rules.

* Each video needs to either be a DIY using our parts or a testimonial about the service you have recieved.

* Videos need to be either shared on our Facebook page or sent to jason@mvpsocialmedia.com.

* All videos will be added to our YouTube channel. The video with the most likes will win the grand prize.

* 1st Place Wins--- $500 American Express Debit Card
* 2nd Place Wins--- $250  American Express Debit Card
* 3rd Place Wins--- $100  American Express Debit Card

Winners will be announced April 1st!

Ask any questions you may have and good luck!

Wednesday, January 23, 2013

Microwave oven maintenance

Originaly Appeared on www.repairfaq.org
Most people do not do anything to maintain a microwave oven. Many will go for 20 years or more without any noticeable decline in performance. While not much preventive maintenance is needed, regular cleaning at least will avoid potentially expensive repairs in the future. Most of this involves things that don't require going inside and anyone can do. A shop that wants to add on preventive maintenance while doing some other repair is just trying to pad their wallet - anything that was required to ensure the health of the oven should have been included.
 
 
  • Clean the interior of the oven chamber after use with a damp cloth and some detergent if necessary. Built up food deposits can eventually carbonize resulting in sparks, arcs, heating, and damage to the mica waveguide cover and interior paint - as well as potentially more serious damage to the magnetron. If there is any chance of food deposits having made their way above the waveguide cover in the roof of the chamber, remove the waveguide cover and thoroughly clean inside the waveguide as well.
  • Clean the exterior of the cabinet and touchpad in a similar manner. DO NOT use a spray where any can find its way inside through the door latch or ventilation holes, or a dripping wet cloth. Be especially careful around the area of the touchpad since liquid can seep underneath resulting in unresponsive or stuck buttons or erratic operation. Do not use strong solvents (though a bit of isopropyl alcohol is fine if needed to remove sticky residue from unwanted labels, for example).
  • Inspect the cord and plug for physical damage and to make sure the plug is secure and tight in the outlet - particularly if the unit is installed inside a cabinet. (Yes, I know it is difficult to get at but I warned you about that!.) Heat, especially from a combination microwave/convection oven or from other heat producing appliances can damage the plug and/or cord. If there is evidence of overheating at the outlet itself, the outlet (and possibly the plug as well) should be replaced.
    
  • Periodically check for built up dust and dirt around the ventilation holes or grills. Clean them up and use a vacuum cleaner to suck up loose dust. Keeping the ventilation free will minimize the chance of overheating.
  • Listen for any unusual sounds coming from inside the oven. While these appliances are not exactly quiet, grinding, squealing, scraping, or other noises - especially if they were not there when the oven was new - may indicate the need for some more extensive maintenance like belt replacement or motor lubrication. Attending to these minor problems now may prevent major repairs in the future.
  • Keep your kitchen clean. Yes, I know, this isn't exactly microwave specific but cockroaches and other uninvited guests might just like to take up residence inside the electronics bay of the oven on the nice warm controller circuit board or its neighborhood and they aren't generally the tidiest folks in the world.
CAUTION: Do not spray anything into the holes where the door latch is inserted or anywhere around the touchpad as this can result in internal short circuits and costly damage - or anywhere else inside, for that matter. If you do this by accident, immediately unplug the oven and let it dry out for a day or two.
 
 
 
Reproduction of this document in whole or in part is permitted if both of the following conditions are satisfied:
  1. This notice is included in its entirety at the beginning.
  2. There is no charge except to cover the costs of copying.

Monday, January 21, 2013

Here's Your Chance!

Here's your chance to have a picture of yourself or someone you love as the Appliance Zone profile pic for a day on Facebook. Here's a copy of the original post.

Let's try something fun here. Take a picture of yourself holding a homemade sign with "I Love Appliance Zone" on it and then share them here. Each picture that we recieve between now and 8am Tuesday morning central will get to be Appliance Zones profile picture for a day. Enjoy and be creative :)

Show us what you've got!

Friday, January 18, 2013

GE Microwave Troubles SCA1000HBB04

More great advice from Kelly on the Appliance Zone Repair Forum!

Question: I have a GE Profile over the stove combination microwave/conventional oven, model SCA1000HBB04. It ran fine for a couple of years but started making a humming/buzzing noise if the door was shut even if no actions were selected. I tested it by putting in a mug with 1 cup of water, shutting the door and setting the timer for 2 minutes. I did not select either the microwave or conventional oven settings but the water was boiling by the end of the 2 minutes. The microwave has since been unplugged. The happens each time I plug in the microwave though for a couple of months it would work normally when plugged back in. Now it always hums/buzzes if plugged in.
Other symptoms/conditions:
-turntable does not turn when heating like this,
-light does not come on when heating like this,
-both turntable and light appear to work normally if I turn on the microwave to heat normally though it only appears to heat on high (100% power) regardless of the power setting I chose,
-the door must be closed for the humming/buzzing to start.
Any ideas?

Answer from Kelly Smith on the Appliance Zone Repair Forum: Hi, sorry to hear of your microwave trouble. The Smart Board has a relay that powers the magnetron. That relay has a set of contacts in it that have become welded together. The Smart Board, number 1655 in the diagram, will need to be replaced.


Link to the actual post.

Tuesday, January 8, 2013

Tips on Maintaining Your Dishwasher

Most of us don't think about cleaning the dishwasher very often. After all, if the dishes are getting cleaner, shouldn't the dishwasher get cleaner, too? Unfortunately, debris and deposits do build up over time, and some of them reduce the performance of the dishwasher. Fortunately, dishwashers don't need cleaning very often and it's not hard to clean them. Here's how:




Steps:

1. Use your dishwasher regularly.
It will help to prevent food and other debris from building up in there, reducing the need to clean it.

2. Run the dishwasher or wait until just after you've run it, then empty the dishwasher completely. Do the other steps with the dishwasher empty.

3. Check all the spinning arms.Look to make sure all the holes are open so that water can run through them freely. The hole in this photo has accumulated some debris.

4. Clear any debris out of the holes in spinning arms.Use fine pointed or needle-nose pliers if you have some. Otherwise, try a toothpick or something similar. Take care not to scratch anything if you're using a tool with a metal point. If these holes are very small, bend a fine wire with a tiny hook on one end. Thread the wire through the opening most distal from the center of the arm. Each time you do this a small amount of debris will come out. This is time consuming. Another option is to drill a much larger hole at the end of the arm. Run the washer to eject the matter, then plug the bigger hole with a stainless steel screw.

5. Wipe around the edges of the door and around the gasket.This space doesn't get washed during the dishwasher cycle. Use a damp cloth and, if you like, a bit of mild spray cleaner. An old toothbrush or other soft, household brush can help get into corners and up under the gasket.

6. Clean under the bottom of the door.In some dishwashers, this is a dead spot where water doesn't go, so it can accumulate debris. Wipe this off.

7. Inspect the bottom of your dishwasher around the drain.
There will be a grate or grill around it, under the arm. This is where wastewater goes. Look for debris clogging up this area. You shouldn't have to clean this often if you're careful about what you put in your dishwasher, but you should remove any solid matter that builds up, especially bits of paper, shards of broken dishes, gravel, etc. You may be able to pick up solid objects accumulated on the outside by hand. If you think stuff has gotten down inside, you'll have to do some simple disassembly to get at it. Start by unplugging. These outlets have been labeled to reduce confusion.

8. Remove hard water deposits or scale, if needed.Run one cycle of your dishwasher empty, with a mild, food acid of your choice. Do this after you've done the other cleaning steps here, so that it will also take care of anything your cleaning missed or knocked loose. A "light" or short cycle is usually sufficient. Place powders into the detergent cup. Place liquids in a right-side-up cup or bowl in the top rack. Use whichever of the following is on hand or inexpensive:

:: Lemonade drink mix or lemon-flavored Kool-Aid mix. Don't use strong colors that might stain. There is no need to add the sugar.
:: Tang (powdered)
:: Lemon juice
:: Distilled white vinegar
:: A dishwasher cleaning product

9. Remove mildew or mold with bleach. Run a separate cycle from any acid cleaners you have used and never mix bleach with other cleaners or with dishwasher detergent.

- If mold and mildew is a problem, leave the dishwasher loosely open for a while after each cycle to allow it to dry out.
- Avoid using bleach and detergents containing bleach if your dishwasher has a stainless steel interior or door.
- Bleach is a very strong chemical, both on you and on your dishwasher, so use it sparingly and only when necessary.

10. Tackle rust stains. - Use a dishwasher-safe rust remover [2] for the stains themselves, but ask how they got there in the first place.
- If the finish is chipping or flaking off the wire baskets in your dishwasher, try a paint-on sealant made just for dishwasher racks. Pull out the racks and check the bottoms, too. If the damage is severe or widespread (not just a few tines but all of them), see if you can replace the entire rack. Online stores sell a wide variety of appliance parts, so your replacement part may be very easy to find.
- If your water has a lot of iron or rust in it, rust may be beyond your control. If possible, address the problem at its source. If the problem isn't rusty pipes, water softeners can remove a limited amount of iron from water but they mostly work by exchanging minerals that are hard to clean off surfaces for salts that are relatively easy to clean. Filters do exist to remove iron from water and might be worth looking into if your water is extremely high in iron.

11. Spray the front of your dishwasher with a mild spray cleaner of your choice and wipe it with a sponge or soft cloth.Pay particular attention to the controls and the handle. Also, don't miss the little ledge between panels. It tends to collect dirt.

12. Refill your dishwasher's rinse aid dispenser about once per month.Rinse aid helps to prevent spots on your dishes. Unscrew the round knob in the dishwasher door and pour in rinse aid according to package directions or your dishwasher's manual. Depending upon your specific water chemistry, you may be able to substitute white vinegar for a "rinse aid." Experiment and see if this is right for your dishwasher.

:: Don't use rinse aid if you have a water softener[4].
:: Solid rinse aids are available. If you forget to refill liquid rinse aid, the solid ones are more visible, so they may help you remember.
:: If you prefer, some dishwasher detergents now have built-in rinse aid.

13. Clean the flatware basket with a brush if there is any accumulated debris.Liquid dish soap will help.
 
From the Appliance Zone Repair Forum

Wednesday, December 26, 2012

Amana XRSS287BB Fridge/Freezer Q & A

Question: We have replaced the HV Control but cannot remove the Water/Ice Dispenser unit from the front of the freezer door, to allow us to change over the LV control unit.
Any ideas or tips on removing this black plastic unit? Answer from Kelly Smith on the Appliance Zone Repair Forum: Hi, thanks for your inquiry. If you remove the water drip tray at the base of the dispenser, are the screws behind it? Will the facade pull loose once they are removed? 

For more great tips like this visit the Appliance Zone Repair Forum

Monday, December 17, 2012

Time & Date of the Next Giveaway!

Within 2 hours of this post the next appliance trivia question will be added to our Facebook page. Remember, the first correct answer wins the gift package from Appliance Zone!