DIY Tip: Fixing a Leaky Refrigerator

Refrigerator Is Leaking Water

Troubleshoot
A pool of water spreading from under your refrigerator or cabinets is never a good thing. Refrigerators use a significant amount of water to conduct their business. Occasionally, problems pop up that cause this water to start leaking. Repairing the situation of a leaking refrigerator first requires a little troubleshooting to determine the exact cause. Once you find out what the cause is, the solution to your wet floor is relatively easy to figure out.

Water Inlet ValveIf the refrigerator is leaking water the water valve may be cracked or have a loose fitting. If the water inlet valve does not shut off properly and the water pressure is good, replace the water inlet valve.

Water Tank Assembly
The tank can sometimes be made up of coiled tubing and is usually located behind the crisper drawers, behind a panel in the refrigerator section. If a leak is discovered, replace it.
Drain Pan
Your leaking refrigerator may just have a cracked or damaged drain pan. Your fridge regularly drains water into this pan to prevent water pooling in the fridge itself. Evaporation takes care of the rest. Look underneath your fridge where the drain pan sits and pull it out for inspection.
Water Filter
If the refrigerator is leaking water the water filter housing, head, or filter itself may be the issue. The filter itself might not be installed correctly. Be sure it is installed properly. As for the filter housing and head be sure to inspect them thoroughly and replace it if any cracks or defects are found.
Clogged or Freezing Defrost Drain
If your leaking refrigerator is draining inside as opposed to onto your floor, you're probably dealing with a clogged defrost drain. This defrost drain can become clogged with debris or, more often, it freezes shut. Look in your refrigerator manual to locate your defrost drain, and take the appropriate steps to unclog it (inundating your drain with warm water will often do the trick).

Appliance Zone New and Improved Repair Forum

If you are one of the over 15,000 registered users of the Appliance Zone Repair Forum then you know what the benefits are. Repair tips from qualified technicians on everything from refrigerator, stove, and dishwasher repair to general technical support are what you'll find. The help is still the same but with a new look and many state of the art user controls and sharing options.

 



 Technicians Kelly, Sam and Barry are on the forum to answer your repair questions. Not sure what part you need? These guys will get you set up with links to the actual parts. Having trouble getting the part installed? Kelly, Sam and Barry will walk you through it and even share diagrams of your machine if needed. What more could you ask for?

Interactive polls, numerous ways to log in and the ability to share your post across social media are a few more additions to the Appliance Repair Forum. Stop by and register today. It's quick, easy and will save you a ton of money on repair costs!

Kenmore 11081860110 Washing Machine That Fills, Spins and Drains but Will Not Agitate

Here is a transcript of a recent online posting of a Kenmore washing machine repair issue from the Appliance Zone Repair Forum. Hopefully it will give you some guidance if you have the same issue. For any other repair questions make sure to check out the Appliance Zone Repair Forum!

Question:

We have a Kenmore 11081860110 that fills, spins and drains but will not agitate.
In Agitate area of dial (any agitate area) Motor does not run but timer ticks.
I'm also having trouble reading the wiring diagram.

Tech:

Thank you this could be two things ,either a timer contact internally in the timer .
Or the drive motor itself .
for agitation it turns one way for drain and spin it turns the opposite way .
you would have to measure voltage to the motor to see which it is.

Question:

I think the motor is fine.
Here are the motor resistance readings with harness disconnected:

Motor Harness
Open GRN
W W
NoPin Open
NoPin Open
Open RED

Meter Resistance
PROBE PROBE 0.3
Motor
W BLU 1.5
W W/BLK 0.3
YEL RED 7.6

BLK YEL 7.6

BLK W >20M
BLK W/BLK >20M

I remember *somewhere* reading that for a direct drive if you swap 2 wires and put it in
"SPIN" then it should agitate, (assuming it spins in the normal configuration). I haven't found
that *somewhere* again. Would this work as a test?

Also on the distorted, difficult to read wiring diagram I have (3351735) I assume the #s
next to the switches are the timer positions and that the lack of odd "SW. Function's was
for "readability", is that correct?

I suspect the timer (3951734) since I hear no 60Hz from the motor in the agitate mode.

I have the tub filled enough to run on low level.

In the "Cotton/Sturdy" mode I suspect I should see low resistance across the power plug in the agitate mode as I do in the spin state.

Resistance across plug
Cotton/sturdy spin 1.8
Permanent Press spin 2.28K
Delicate spin 2.28K

After spraying timer with contact cleaner
Resistance across plug
Cotton/sturdy spin 1.8
Permanent Press spin 2.25K
Delicate spin 2.25K

Cotton/sturdy agitate 2.25K
Permanent Press spin 2.25K
Delicate spin 2.25K

Tech:

Just go down to the motor at Yellow and Red with the unit in an agitation mode check for 120 volts A/C if you have voltage it the motor if no voltage it is the timer 1

Question:

There is a momentary jump on the DVM set at 200VAC then returns to 0.00.
Based on this I'll get a new timer and post the resolution here.

Tech:

Yes that sounds like the issue .good luck

Leaky Washing Machine

Do you have a leaky washing machine but can't seem to figure out where the water is coming from? Here are a few tips to point you in the right direct. If you're still unsure then head over to our repair forum at http://forum.appliancezone.com .

Here are some of the common areas that your washer may leak:

Inlet Hose Connections - Check for drips around the supply hose connection on the back of the washer as it fills with water. If the hoses are old, corroded or rusted replace them. But if they're in good shape you can replace just the hose's internal washers.

 

Hose Connectors - Open the cabinet and start the fill cycle. These hoses tend to leak around a worn out clamp, but the hoses themselves can also crack and break. Identify what is causing the leak and replace it.

 

Pump - Open the cabinet and check around the pump. The pump will typically leak around the pulley. If you notice this, the pump will need to be replaced.

Model Number Search Now Available on ApplianceZone.com

Since Appliance Zone opened its doors in 2008, customers have persistently requested the ability to search their appliance' model numbers so they can research and locate parts more easily on their own. For many years we have attempted to find a comprehensive solution to appease this demand, but have been unsuccessful, until now.

 

To use the model look-up simply click on the "Search by Model" tab at the top of the Start Here box on our home page. Then just start typing in your model number. As you type you will notice the model options available for what you've typed so far, making it easier for you to select the correct number for your appliance. Once your full model number has been inserted, click "GO!" to view all of the available parts for your model. If you still have trouble locating your part, our customer service reps are available via chat to assist.

Appliance Zone has always tried to empower customers with a DIY attitude. We've been working hard the past few months, developing new tools and incentives to assist and reward our loyal customers. This new model number search feature is just one of many to come.

So, be sure to stay tuned for more exciting announcements from ApplianceZone.com!

What is the Appliance Zone Repair Forum?

The Appliance Zone Repair Forum is the premier spot to get all of your repair questions answered free of charge. Are you stuck on how to repair an issue with your appliance? Just post your question on this forum and you'll get a quick and reliable answer! Check it out live ----> HERE!